Mandrel tube bending machine

tube diameter 60 mm︱wall strength 3 mm︱bending radius min. 2 x Rohr-Ø ÷ R200 mm︱bending angle 0 - 180 °︱gas tube pipelines 2" (60.,3mm) mm︱speed stufenlos 0,5 - 2,0 ︱total power requirement 1,5 kW︱weight of the machine ca. 0,7 t︱

---

- Powerful mandrel bending machine up to 2 "gas pipe (60.3mm) in semi-automatic design (6000 mm pipe slide length) - Electromechanical drive of the bending axis - hydraulic clamping - mandrel feed / extract - 30 programs x 9 bending angle + correction angle

tube diameter 6 - 28 mm︱wall strength 2 mm︱bending radius min. 2 x D ︱Control IPU 20 ︱bending radius max. 5,0 x D mm︱bending angle max. 190 °︱arbor length 3000 mm︱operating pressure 180 bar︱hydraulic motor 4 kW︱weight of the machine ca. 900 kg︱dimensions of the machine ca. 3,8 x 1,1 x 1,3 m︱Electric 400 Volt ︱Bending segments 15-20-26-28 mm︱Bending mandrels 4 ︱Operation panel 0,5 x 0,6 x 1,03 m︱Double Foot pedal ︱Machine manual ︱Condition: ready for operation ︱Video available on our website. ︱

---

Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood in the warehouse and has not worked since then. Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

tube diameter 25 mm︱wall strength 2 mm︱bending radius min. 10 mm︱Control ︱bending radius max. 75 mm︱total power requirement 11 kW︱weight of the machine ca. 1,45 t︱dimensions of the machine ca. m︱

---

tube diameter max. 38 mm︱wall strength 2 mm︱bar material dia. min. 10 mm︱bending radius min. 35 mm︱bending radius max. 150 mm︱pull up length of tube 4500 mm︱bending angle max. 180 °︱accuracy of bending angle ± 0,2 °︱total power requirement 7,5 kW︱weight of the machine ca. 1,2 t︱dimensions of machine L x W x H 6,7 x 1,4 x 1,9 m︱

---

- with 8-pos. bending angle pre-selection - crawler gear control - positioning device by hand - tube twist device Following bending tools are with the machine: - ø 10 mm, radius 27,5 mm - ø 12 mm, radius 35 mm - ø 12 mm, radius 56 mm - ø 15 mm, radius 35 mm - ø 15 mm, radius 57,5 mm - ø 18 mm, radius 35 mm - ø 18 mm, radius 59 mm

neu ︱ ca. 12 - 14 Wochen ab Auf ︱ Italien ︱ 64000 €︱ 1286.4 €︱ 76 mm︱ 4535 mm︱ 1145 mm︱ 1400 mm︱ 1488 kg︱ 18 cm³︱ 76 x 3,6 mm︱ 76 x 2,3 mm︱ 70x70x3 mm︱ 70x50x3 mm︱ 70x50x6 mm︱ 76 mm︱ 200 mm︱ 10 mm︱ 195 °︱

---

Three-phase NC electric-hydraulic mandrel bending machine up to 76 mm with 1 controlled axis (bending axis C) New TCPlus control • 7” colour touch screen • Icons for ease use • Automatic mode, manual mode, programming mode • Advanced OFFSET function • Easy language change • Auto-tuning of the main machine components • Programmable bending speed for each single bend of the program • Unlimited programs possibility (USB port) • Every program can contain up to 30 different bends • Available extensions of 2 meters each (optional) • Tie bar (optional - art. TB80-TI)

neu ︱ ca. 12 - 14 Wochen ab Auf ︱ Italien ︱ 29300 €︱ 594.79 €︱ 50 mm︱ 4000 mm︱ 950 mm︱ 1250 mm︱ 430 kg︱ 6 cm³︱ 50 x 3,31 mm︱ Ø 1”1/4 mm︱ Ø 50 x 2,5 mm︱ 40 x 40 x 4 mm︱ 25 x 50 x 6 mm︱ 50 x 25 x 2,7 mm︱ 60 mm︱ 200 mm︱ 20 mm︱

---

With mandrel 3 m length Can be used with or withoud mandrel Two bending speeds Programmable bend sequencing and mandrel retraction Independent clamp and pressure die adjustment Micrometer wiper die adjustment Auxiliary system for stabilizing the hydraulic slide pressure Quick tool change system With pneumatic material clamping and DRO system for linear and rotational positioning ALTERNATIVELY: model with mandrel 6 m length price on request

neu ︱ ca. 12 - 14 Wochen ab Auf ︱ Italien ︱ 121200 €︱ 2411.88 €︱ 76 mm︱ 5700 mm︱ 1100 mm︱ 1550 mm︱ 2700 kg︱ 25 cm³︱ 76,1 x 6,8 mm︱ 2”1/2 mm︱ 76,2 x 3,8 mm︱ 63,5 x 63,5 x 5,6 mm︱ 70 x 50 x 8 mm︱ 70 x 50 x 6 mm︱ 79 mm︱ 250 mm︱ 20 mm︱

---

FST clamping system (Patented) 6 programmable axes: carriage mobement (Y1 axis), bending plane rotation (B axis), bending angle (C axis), pressure die movement (X2 axis), booster (Y2 axis) and hydraulic mandrel movement (Y3) Touch screen control with 3D display of the tube Anti collision system tube/machine, tube/floo, tube/external elements and tube/equipment Importing files in iges and dxf format (optional) Integrated Wi-Fi FURTHER MANDREL LENGTHS ON REQUEST

neu ︱ ca. 12 - 14 Wochen ab Auf ︱ Italien ︱ 35300 €︱ 716.59 €︱ 64 mm︱ 4000 mm︱ 950 mm︱ 1250 mm︱ 850 kg︱ 10 cm³︱ 64 x 3,3 mm︱ 2" mm︱ 60,3 x 2,2 mm︱ 60 x 60 x 2 mm︱ 40 x 60 x 4 mm︱ 60 x 40 x 3 mm︱ 76 mm︱ 200 mm︱ 20 mm︱

---

with mandrel 3 m length FST closure system (Patented) with auxiliary system for stabilizing the hydraulic pressure of the slide Programmable C-axis bending Positioning of the 2-axis manual spindle carriage (Y1=Feed and B=Rotation) with high resolution encoder and standard adjustable mechanical stops Multifunction control keyboard integrated in the machine body with microprocessor control with multifunctional menu 30 programs of 9 bends each can be memorized Screen for digital display for carriage feed (Y1 Axis) and rotation (B Axis) External pressure gauges for easy setting of the system and closing pressure Variable bending speed up to 4 rpm (Inverter versions) Pneumatic chuck ALTERNATIVELY: model with mandrel length 1,5 / 4 / 6 mm

sheet width 3000 mm︱plate thickness 6 mm︱distance between columns / mm︱

---

sheet width 3100 mm︱plate thickness 6 mm︱voltage 380 V︱control CYBELEC CybTouch ︱down holder 14 Stück︱cutting angle 1,2 °︱total power requirement 11 kW︱weight of the machine ca. 6.300 kg︱dimensions of the machine ca. 4000x2100x1640 mm︱

---

Equipment: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 * Backgauge preselection - X axis * Cutting gap adjustment * Quantity * Cutting length limitation * Material preselection, including sheet thickness * Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) * on ball screws * autom. can be folded up at max. Traverse path, for longer cuts - 1x side stop - 2x front support arms - Ball casters in the front support table - hinged finger protection, with safety switch - BOSCH / HOERBIGER hydraulic system - SIEMENS electrical system - light barrier behind the machine (safety device) - foot switch - CE mark / declaration of conformity - User manual: machine u. Control in German Special equipment: - pneumatic sheet holding device (monoblock)

sheet width 3060 mm︱plate thickness 10 mm︱back stop - adjustable 1000 mm︱cutting angle 1,5 °︱weight of the machine ca. 10500 kg︱

---

Equipment/accessories: - CYBELEC Cybtouch touchscreen controller - NC controller for backgauge preselection, cutting gap adjustment, number of pieces, cutting length and material preselection - Sheet holding device - 1 side stop with scale, T-slot and tilting cam - 2 front support arms - Cutting line lighting - Cutting gap adjustment - Cutting length limiter - Hinged finger guard with limit switch - Motorized backgauge 1,000 mm travel - recirculating ball screws - Ball rollers in the table - foot switch

sheet width 3100 mm︱plate thickness 10 mm︱cutting angle 2 °︱down holder 14 Stück︱no. of strokes 13 Hub/min︱throat 350 mm︱oil volume 260 l︱control CYBELEC CybTouch 8 ︱total power requirement 22 kW︱weight of the machine ca. 10.550 kg︱dimensions of the machine ca. 4000x2250x2050 mm︱

---

Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German

sheet width 2040 mm︱ 4 mm︱sheet thickness for stainless steel 2 mm︱total power requirement 7,5 kW︱rear stop 750 mm︱weight of the machine ca. 2600 kg︱dimensions 2810 x 2230 x 1360 mm︱

---

sheet width 3100 mm︱plate thickness 10 mm︱cutting angle 2 °︱down holder 14 Stück︱no. of strokes 13 Hub/min︱throat 350 mm︱oil volume 260 l︱total power requirement 22 kW︱weight of the machine ca. 10.550 kg︱dimensions of the machine ca. 4000x2250x2050 mm︱

---

Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German

sheet width 3100 mm︱plate thickness 13 mm︱thickness at "Niro-steel" 8 mm︱control CYBELEC CybTouch ︱down holder 14 Stück︱cutting angle 2,0° °︱total power requirement 22 kW︱voltage 380 V︱no. of strokes 11 Hub/min︱weight of the machine ca. 12.100 kg︱dimensions of the machine ca. 4000x2240x2235 mm︱

---

Accessories / equipment: - CYBELEC-CybTouch control panel with digital display for backgauge - hydr. Cutting gap adjustment via control - 1 side stop - 4 front lifting arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Ball rolls in the table - motorized back gauge 1.000 mm travel with recirculating ball screws,    automatically start at the end of the stop - Shear knives for stainless steel cuts as standard - Photocell behind the machine - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - Operating instructions in German

sheet width 3100 mm︱plate thickness 6 mm︱voltage 380 V︱control CYBELEC CybTouch ︱down holder 14 Stück︱cutting angle 1,2 °︱ 20 ︱total power requirement 11 kW︱weight of the machine ca. 5700 kg︱dimensions of the machine ca. 4000x2100x1640 mm︱

---

Accessories / equipment: - CYBELEC Cybtouch touch screen controller - NC controller for backgauge, gap adjustment, number of pieces, cutting length - 1 side stop with scale, T-groove and tilting cam - 2 front support arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Folding finger guard with limit switch - motorized back gauge 1.000 mm travel - Ball screws - Photocell behind the machine - Ball rolls in the table - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - CE mark / Declaration of Conformity - Operating manual: Machine and control in German

sheet width 1350 mm︱ 3 mm︱sheet thickness for stainless steel 1,5 mm︱rear stop 600 mm︱total power requirement 3 kW︱weight of the machine ca. 1150 kg︱dimensions 2030 x 1940 x 1220 mm︱

---

sheet width 3050 mm︱plate thickness 6 mm︱back stop - adjustable 1000 mm︱cutting angle 1,5 °︱0 17 St.︱total power requirement 11 kW︱quantity of oil 180 l︱weight of the machine ca. 5950 kg︱

---

sheet width 2550 mm︱ 4 mm︱sheet thickness for stainless steel 2 mm︱rear stop 750 mm︱total power requirement 7,5 kW︱weight of the machine ca. 3050 kg︱dimensions 3300 x 2230 x 1360 mm︱

---

sheet width 3100 mm︱plate thickness 4,00 mm︱distance between columns mm︱total power requirement 7,50 kW︱weight of the machine ca. 4,20 t︱dimensions of the machine ca. m︱

---

- CNC controlled back gauge 10 – 1000mm - central cutting gap adjustment - Pneumatic sheet metal support - Angle stop 2500 mm - 3 support arms

sheet width 3050 mm︱plate thickness 16 mm︱distance between columns - mm︱back stop - adjustable 1000 mm︱total power requirement kW︱weight of the machine ca. 15 t︱

---

Acc.: electr. back gauge with DRO, table extensions

sheet width 3100 mm︱plate thickness 6,00 mm︱thickness at "Niro-steel" 4,00 mm︱cutting angle 2,0 °︱no. of strokes 15 Hub/min︱back stop - adjustable max. 1000 mm︱down holder 14 Stück︱work height max. 865 mm︱Column width 3515 mm︱throat 50.0 mm︱Control D-Touch 7 ︱oil volume 200 l︱engine output 15.0 kW︱voltage 400 V︱weight 7.650 kg︱range L-W-H 4110 x 2200 x 2100 mm︱

---

** from a maintenance workshop (vehicle construction) ** maintained condition (!!) ** New price ~ 41.000 euros ** Special price on request Furnishing: - robust electro-hydraulic sheet metal shears - CNC control unit D-Touch 7 control ("touchscreen") * Anti-reflective, robust 7" color touch screen control panel * easy positioning to the desired size * Positioning accuracy 0.1 mm * unlimited material definition in the material library * Intuitive menu navigation * Separate display for actual and target value * Clearance function of the back gauge * Cutting length control via adjustable stroke length * Cutting counter * Automatic stop of the machine when the programmed cuts are reached - CNC electric motor adjustable back gauge * Travel distance max. 1,000 mm * Backgauge adjustment via ball screws and linear guides - constant, low cutting angle for optimal cutting results - heavy steel construction in welded construction - Ergonomically positioned and clear control panel - Hold-down device arranged close to the cutting edge - split, fold-up finger protection 1000 mm - Self-regulating hold-down pressure - manual cutting gap adjustment via adjustment lever * with central adjustment lever on the right side of the stand - Light barrier for the backgauge area - 1x side stop .. L = 1500 mm - 2x support arms.. L = 1000 mm each - wide sheet metal supports with ball rollers - mobile foot switch with emergency stop function - high-quality and regrindable knives - Hydraulic components MANNESMANN REXROTH or BOSCH - Electrics SIEMENS or TELEMECANQUE - Operation manual

sheet width 3100 mm︱plate thickness 6.0 mm︱thickness at "Niro-steel" 4.0 mm︱cutting angle 2,0 °︱no. of strokes 15 Hub/min︱back stop - adjustable max. 1000 mm︱down holder 14 Stück︱work height max. 865 mm︱Column width 3515 mm︱throat 50.0 mm︱Control D-Touch 7 ︱oil volume 200 l︱engine output 15.0 kW︱voltage 400 V︱weight 7.650 kg︱range L-W-H 4110 x 2200 x 2100 mm︱

---

** from a maintenance workshop (vehicle construction) ** maintained condition (!!) ** New price ~ 41.000 euros ** Special price on request Furnishing: - robust electro-hydraulic sheet metal shears - CNC control unit D-Touch 7 control ("touchscreen") * Anti-reflective, robust 7" color touch screen control panel * easy positioning to the desired size * Positioning accuracy 0.1 mm * unlimited material definition in the material library * Intuitive menu navigation * Separate display for actual and target value * Clearance function of the back gauge * Cutting length control via adjustable stroke length * Cutting counter * Automatic stop of the machine when the programmed cuts are reached - CNC electric motor adjustable back gauge * Travel distance max. 1,000 mm * Backgauge adjustment via ball screws and linear guides - constant, low cutting angle for optimal cutting results - heavy steel construction in welded construction - Ergonomically positioned and clear control panel - Hold-down device arranged close to the cutting edge - split, fold-up finger protection 1000 mm - Self-regulating hold-down pressure - manual cutting gap adjustment via adjustment lever * with central adjustment lever on the right side of the stand - Light barrier for the backgauge area - 1x side stop .. L = 1500 mm - 2x support arms.. L = 1000 mm each - wide sheet metal supports with ball rollers - mobile foot switch with emergency stop function - high-quality and regrindable knives - Hydraulic components MANNESMANN REXROTH or BOSCH - Electrics SIEMENS or TELEMECANQUE - Operation manual * Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008-9325322

sheet width 3100 mm︱plate thickness 6.0 mm︱thickness at "Niro-steel" 4.0 mm︱down holder 14 Stück︱no. of strokes 20 Hub/min︱cutting angle 1.2 °︱control CYBTOUCH 6 ︱work height max. 800 mm︱oil volume 150 ltr.︱total power requirement 11.0 kW︱weight 7060 kg︱range L-W-H 4000 x 2410 x 1610 mm︱

---

** well maintained condition (!!) ** current new price approx. 42.000 euros ** Special price on request -------------------------------------------------- Robust electro-hydraulic CNC swing cutting shears * including CYBELEC CNC touch screen control * including CNC electro-hydraulic cutting gap adjustment -------------------------------------------------- Furnishing: - CNC electro-hydraulic swing cutting shear - including CYBELEC CNC touch screen controller, model “CybTouch 6” - some functions of the CNC control: * Backgauge preselection - X axis * Cutting gap adjustment * Number of pieces * Cutting length limitation * Material selection, including sheet thickness * Cutting line lighting (cutting on outline) .. and many more - motorized back gauge, travel = 5.0 - 1.000 mm (X axis) * on ball screws * Automatically folds up at maximum travel distance, for longer cuts * including retraction function selectable ("swing-away function") * Positioning accuracy 0.10 mm * Travel speed 80 mm/sec. - 1x side stop, with T-slot and mm scale - 2x front support arms, with T-slot and mm scale - Ball rollers in the front support table - hinged finger protection, with safety switch * Finger protection with viewing windows for cutting after cracking - Section line lighting with silhouette - BOSCH/HOERBIGER hydraulic system - SIEMENS electrical system - Light curtain behind the machine (safety device) - freely movable foot switch - CE mark/declaration of conformity - Operating instructions + circuit diagram + hydraulic diagram * Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008-9325339