Bar Stock Carrier

diameter 5 - max. 51 mm︱Guide channels max. 6 ︱Spindle height ca. 1020 mm︱bar material dia. min. 5 mm︱bar material dia. max. 51 mm︱max. bar length 6200 mm︱Remaining piece design 600 mm︱accumulator pressure min 6 bar︱coolant capacity 1500 l/min︱control SPS ︱total power requirement 2,3 kW︱weight of the machine ca. 3,2 t︱dimensions of the machine ca. 7,2 x 1,55 x 1,6 m︱

---

used multi-channel bar feeder ecoPROFImat 42.6 RK3 / 6000 III Condition: As NEW, approx. 500 operating hours incl: Guide channels Ø 20/24/44 Material slide Ø 19/22/42 spindle insert tubes Ø 20/24/44 Interface to the machine set up for Mazak QT 200 MS x 500 Area of application: Ideal for small to medium batch sizes Features: Minimal changeover times, channel change at the touch of a button Optimum running properties 3 to 6 guide channels, high dead weight Maximum running smoothness, hydrodynamic bearing, 360° closed guide channels High level of operating convenience thanks to an 18 cm (7") widescreen touch display. Reliable feeding of rotationally symmetrical profile material Electronic synchronisation device, optimum material guidance between magazine and machine with hydrodynamic telescopic system. Simple changeover from long to short turning operation at the touch of a button Special features: Simple change of the spindle insert tubes through axial displacement of the magazine. Process-integrated remnant removal to the rear (remnant length 600 mm) Machine-friendly, vibration-absorbing design

Bar diameter 6 - 65 mm︱Bar Length 300 - 1250 mm︱Length 1600 mm︱Depth 1048 mm︱Height 1010 / 1410 mm︱Weight 375 kg︱

---

diameter 35 - max. 65 mm︱Guide channels 6 ︱control SPS ︱max. bar length 3.200 mm︱bar material dia. min. 35 mm︱bar material dia. max. 65 mm︱total power requirement 2 kW︱weight of the machine ca. 2,0 t︱dimensions of the machine ca. 4,0 x 1,1 x 1,6 m︱

---

Multi-Channel-Bar-Feeding-System BREUNING IRCO - 65.6 196.6 - has been installed at a Mori Seiki ZL 200 SMC

diameter 15 mm︱length 800 mm︱

---

= bar loading and de-loading magazine for bars up to 15 mmø, bar length 800 mm

diameter 3 - 16 mm︱length 3000 mm︱

---

= bar loading magazin for bar-ø 3 - 16 mm, bar length 3000 mm, capacity for example 23 bars 8 mmø

diameter 26 mm︱length 3200 mm︱Control ︱total power requirement 1 kW︱weight of the machine ca. 1,4 t︱dimensions of the machine ca. 4,5 x 0,8 x 1,35 m︱

---

Bar feeder FMB Turbo 3-26 1 channel and bar pusher for 26mm Bar length max. 3200 mm Was attached to Gildemeister Ergomat TDA 26

bar material dia. 12 - 42 mm︱bar length 3200 mm︱feed speeds 220 mm/sec︱return speed 440 mm/sec︱feed power bis 400 Nm︱compressed air max. 6 bar︱filling capacity 22 Stangen x ø 12 mm︱filling capacity 13 Stangen x ø 20 mm︱filling capacity 7 Stangen x ø 42 mm︱hexagon material bis SW 27 mm︱square material bis SW 20 mm︱total power requirement 0,75 kW︱weight of the machine ca. 0,83 t︱dimensions of machine L x W x H 5,06 x 0,85 x 1,275 m︱

---

= bar loading magazine, compressed air controlled

diameter 42 mm︱length 1500 mm︱voltage 380 V / 50 Hz︱total power requirement 1,1 kW︱weight of the machine ca. 0.4 t︱dimensions of the machine ca. m︱

---

Rod guidance pipe, diameter 42 x 2400 mm length, 2 columns, 1 hydraulic aggregate,

diameter 45 mm︱length 4400 mm︱total power requirement 1,0 kW︱weight of the machine ca. 1,2 t︱dimensions of the machine ca. 5 x 0,4 x 1,2 m︱

---

centre height 130 mm︱spindle bore 18 mm︱ratio 40:1 ︱swivellable - 10° bis 90° °︱groove width 16 / 18 mm︱weight 35 kg︱dimensions of the machine ca. 0,5 x 0,25 x 0,25 m︱

---

Unused semi-universal dividing set: - Spindle in precision tapered roller bearings - Phosphor bronze worm wheel, helix Cr-NI steel, hardened and ground - Translation disengageable for direct sharing - each division 2 to 50 and many divisions to 380 accessories: Tailstock, 2 part washers, centering point, driver and chuck flange Machine dealer with own stock of 1600 m².

centre height 160 mm︱chucking diameter 200 mm︱hollow 54 mm︱

---

/ ︱weight 295 kg︱

---

Center height: approx. 180mm dimension Length: about 480mm Width: about 450mm Height: 280mm Weight: 110kg

/ ︱weight 295 kg︱

---

Center height: approx. 265mm dimension Length: about 800mm Width: about 600mm Forkart Chuck F315 Lining passage: 80mm Weight: 295kg

/ ︱weight 140 kg︱

---

dimension Length: about 430mm Width: approx. 530mm Height: about 370mm Weight: 140kg

/ ︱weight 75 kg︱

---

Center height: approx. 215mm dimension Length: about 370mm Width: about 260mm Height: approx. 340mm Chuck diameter: 190mm Lining passage: 60mm Weight: 75kg NEIGHBOR

centre height 90 mm︱weight of the machine ca. 65 kg︱dimensions of the machine ca. 600 x 300 x 300 mm︱

---

centre height - mm︱

---

centre height 140 mm︱chucking diameter 250 mm︱swivelling range 90 Grad︱weight of the machine ca. 150 kg︱

---

Dividing head swivable of a Heckert FU 400

centre height 390 mm︱passage of steadyrest 220 mm︱chucking diameter 400 mm︱total power requirement / kW︱

---

centre height 250 mm︱total power requirement 0 kW︱weight of the machine ca. 0,250 t︱dimensions of the machine ca. m︱

---

centre height 160 mm︱chucking diameter 160 mm︱indexing 15 °︱groove width 12 mm︱weight 50 kg︱dimensions of the machine ca. 550 x 230 x 200 mm︱

---

- S/N: 1117 - AROWA three-jaw chuck including jaws - indexing every 15°

centre height 76 mm︱centre distance 190 mm︱spindle bore 21 mm︱taper MK 3 ︱weight of the machine ca. 40 kg︱dimensions of the machine ca. 720 x 210 x 215 mm︱collets ︱tailstock ︱dead centres ︱

---

centre height 76 mm︱centre distance 160 mm︱spindle bore 21 mm︱taper MK 3 ︱total power requirement kW︱weight of the machine ca. 20 kg︱dimensions of the machine ca. m︱collets ︱tailstock ︱dead centres ︱

---

centre height / mm︱total power requirement / kW︱weight of the machine ca. / kg︱

---

Make: Peiseler Type: HW710 Diameter: Ø 710mm Weight: approx. 450 kg