Injection-moulding machine (rubber)

clamping force 4.210 kN︱injection volume 2.500 cm³︱screw diameter -- mm︱platen size 710 x 800 mm︱

---

Condition: used, Specification: injection moulding machine for rubber - used clamping unit: - clamping force: 4.210 kN - size of heating platen L/W: 710 x 800 mm - distance between tie bars: 600 x 810 mm - distance upper- lower platen: 715 mm - Opening stroke: 580 mm - Mould height min.: 135 mm Injection unit: - Injection volume max.: 2,500 cm³ - Connection value: 3x 400 V, 50 Hz, N, PE - Connected load: 180 kW - Weight approx.: 16,000 kg - Required floor space approx.: 9.8 m² - Operating hours approx.: 18,000 hours - brushing and air blade mould cleaning

clamping force 11000 kN︱injection volume 12500 cm³︱screw diameter -- mm︱platen size 1000 x 1800 mm︱

---

Condition: used, Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturer clamping unit: - Euromap (size): 11000-25600 - clamping force: 11.000 kN - size of heating platens L/W/H: 1000 x 1800 x mm - Distance upper- lower plate: 1200 mm - Stroke min.: 630 mm - Max. stroke: 1030 mm Injection unit: - Injection volume max.: 12,500 cm³ - Injection pressure: 2050 bar - Dosing force: 118 kN - Control: Siemens S7 - Connected load: 3x 400 V, 50 Hz, N - Total current: 276 A - Back-up fuse: 300 A - Pump drive: 277 bar - Driving power: 45 kW - Weight approx.: 43.8 t Operating hours approx.: 33,130 hours

clamping force 350 kN︱injection volume 58,5 cm³︱screw diameter 28 mm︱platen size 260 x 254 mm︱

---

Condition: used, Specification: injection moulding machine for TPE - used clamping unit: - clamping unit: vertical - clamping force: 350 kN - opening stroke max.: 300 mm - platen distance max.: 500 mm - Mould installation height min.: 200 mm - Clear width between tie bars: 260 x 254 mm - Ejector stroke max.: 80 mm - Clamping unit: VV - Lift of protective bonnet: 500 mm Injection unit: - Screw diameter: 28 mm - Screw L/D ratio: 18.6 - Screw stroke max.: 95 mm - Injection volume max.: 58.5 cm³ - Injection pressure: 1577 bar - Plasticising flow: 8.6 g/s - Injection flow: 85.5 g/s - Connected load: 3x 400 V, 50 Hz - Max. heating power: 5.8 kW - Drive power: 7,4 kW - Total power: 13,2 kW - Hydraulics: 210 bar (tank 65 litres) - Operating hours approx.: 2.659 hours Dimensions L/W/H approx.: 2,047 x 803 x 2,710 mm Footprint: 1.7 m² Weight approx.: 1,670 kg Last maintenance: 01.2021 Incl. granulate conveyor and temperature control unit.

clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱

---

Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive power: 11 kW - Weight without oil: 6,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm

clamping force 1100 kN︱injection volume 1000 cm³︱screw diameter -- mm︱platen size 330 x 500 mm︱

---

Condition: used, Specification: frame injection moulding machine - used clamping unit: - clamping force: 1100 kN - heating platen size: 330 x 500 mm - mould size: 500 x 400 mm - Clear width upper- lower platen: 740 mm - Clamping direction: from below Injection unit: - Injection volume max.: 1000 cm³ - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Control voltage: 24 VDC - Hydraulics Rexroth: 7,5 kW - Control: ECO II / System X20 - Pump capacity: 63 l/min Units are currently still in production and will be available from August. There are 11 identical units, built between 2008 and 2010, available.

clamping force 1.013 kN︱injection volume 400 cm³︱screw diameter 25 mm︱platen size 335 x 400 mm︱

---

Condition: used, Specification: injection moulding machine for rubber - used clamping unit: - clamping unit: vertical - clamping force: 1.013 kN - size of heating platen: 335 x 400 mm (standard) core turning unit Injection unit: - screw diameter: 25 mm - Barrel diameter: 51 mm - Injection volume max.: 400 cm³ - Injection pressure: 1,500 bar - Connection value: 3x 400 V, 50 Hz 42A fuse protection (incl. periphery) - Electrical power: 29,1 kVA - Control: G8 Control - Hydraulics: 250 bar (tank 200 litres) - Further connections: Cooling water inlet/outlet Dimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mm Weight approx.: 2,950 kg Not for sale: Article-specific extensions (demoulding unit, cold runner block with temperature control units) Available as from 01.01.2023

clamping force 450 kN︱injection volume 135 cm³︱screw diameter 35 mm︱platen size 600 x 400 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for TPE - used, from testing department Including PIOVAN dosing unit clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - Clear width: 585 mm - Tool installation height min.: 185 mm - Max. stroke: 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 4 - Ejector stroke: 200 mm Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg

clamping force 250 kN︱injection volume 49 cm³︱screw diameter 25 mm︱platen size 300 x 300 mm︱

---

Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts

clamping force 1000 kN︱injection volume 630 cm³︱screw diameter -- mm︱platen size 500 x 400 mm︱

---

Condition: used, Specification: C-frame injection moulding machine no. 58006, - second-hand clamping unit: - clamping force: 1000 kN - size of heating platen: 500 x 400 x 71 mm - clamping/opening stroke: 350 mm - Closing direction: from below - Side ejector: top, bottom, yes - Sliding table: yes Injection unit: - Injection volume max.: 630 cm³ - Injection pressure max.: 1800 bar - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 53 kW/86 A - Weight approx.: 6,750 kg - Control: B&R ECO - Tank capacity hydraulic oil: 200 l - Pump capacity: 65 l/min - Temperature control units: 2x Regloplas - Temperature control medium: Oil: OMV thermo 32 A second identical unit is available as a potential spare part donor. available. The panel of this unit is in order. The following defects are known for this spare parts donor: - CPU control defective (offer for spare part of CPU available from 06.2023 available). - Unit without heating plates - Spray cylinder leaking The system as a spare parts dispenser can be offered as an option.

clamping force -- kN︱injection volume -- cm³︱screw diameter -- mm︱

---

Condition: used, Specification: Handling System REMAK-Robot - used type: RF5T-CNC/R driving range: - motor-axis stroke Z-axis: 2.000 mm speed: 3.200 mm/s - Teescope Y-axis stroke: 1,500 mm Speed: 4,400 mm/s X-axis stroke: 500 mm Speed: 1,100 mm/s - Pneum. Axes: B = 0/+90 o. +180 degrees C = 0/+90 degrees - Vacuum: 2 x vacuum generator type EZM 131 - Gripper: 2 x spring-return valves - Permissible load (gripper + workpiece): 5.0 kp - E-connection: 480V, 60Hz - Connected load: approx. 3.5 kW, 16A - Control: Bosch Rho3.0, PHG 16 Vers.8.x

clamping force 1.300 kN︱injection volume 230 cm³︱screw diameter 45 mm︱platen size 685 x 685 mm︱

---

Condition: used, Specification: injection moulding machine for TPE - used including Koch dosing unit clamping unit: - clamping force: 1.300 kN - heating platen size: 685 x 685 mm - Clear distance between tie bars: 470 x 470 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 225 mm Injection unit: - Screw diameter: 45 mm x 18D - Injection volume max.: 230 cm³ - Injection part weight: 210 g/hp - Max. injection pressure: 1,670 bar - Screw circumferential speed: 75 m/min - Cylinder heating: 4x 2,200 W - Nozzle heating: 600 W - Connection value: 3x 400 V, 50 Hz - Electrical connection (back-up fuse): 100 A - Weight approx.: 6,380 kg - Oil filling: 260 litres - Operating hours approx.: 64,903 h

clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱

---

Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive power: 15 kW - Weight without oil: 5,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm

clamping force 1.550 kN︱injection volume 135 / 49 cm³︱screw diameter 35 / 25 mm︱platen size -- mm︱

---

Condition: used, Specification: injection moulding machine for TPE - used type: K-TEC 155 S/2F clamping unit 1550: - Clamping force: 1,550 kN - Clear column spacing: 500 x 500 mm - Max. platen spacing: 950 mm - Platen spacing min.: 650 mm - Opening stroke min.: 300 mm - Ejector stroke: 180 mm Injection unit 1: - Screw diameter: 35 mm - Injection volume max.: 135 cm³ - Injection part weight: 125 g - Injection pressure max.: 1.964 bar Injection unit 2: - Screw diameter: 25 mm - Injection volume max.: 49 cm³ - Injection pressure max.: 2.254 bar - Connection value: 3x 400 V, 50 Hz - Engine power: 37 kW - Total heating power: 14.8 kW - Electrical connection (back-up fuse): 160 A - Dimensions W/D/H approx.: 6.200 x 1.750 x 2,100 mm (see sketch) - Weight approx.: 9.000 kg - Operating hours approx.: 53.176 h

clamping force 500 kN︱injection volume 220 cm³︱screw diameter -- mm︱platen size 500 x 320 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for EPDM - used clamping unit: - clamping force: 500 kN - heating platen size: 500 x 320 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 1 Injection unit: - Injection volume max.: 220 cm³ - Connected load: 3x 400 V, 50 Hz

clamping force 350 kN︱injection volume 59 cm³︱screw diameter 25 mm︱platen size 400 x 400 mm︱

---

Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power: 15,6 kW - Connection value: 3x 400 V, 50 Hz - Electrical connection (pre-fuse): 50 A - Weight approx.: 1,650 kg - Oil filling: 190 litres - Switch cabinet: 150 kg - Operating hours approx.: 1,100 h

clamping force 2500 kN︱injection volume 2x 190 cm³︱screw diameter 45 mm︱screw length 22 D ︱platen size 510 x 670 mm︱

---

Condition: used Specification: Vertical Injection Moulding Machine for Rubber - second-hand - clamping force: 2500 kN - screw diameter: 45 mm - screw length: 22 D - screw speed: max. 300 rpm - injection volume: 2 x 190 cm3 - Injection pressure: 1900 bar - Number of heating zones: 5 - open nozzle with nozzle head - Clear column spacing: 510 x 670 - Mains supply voltage: 380 V, 50 Hz - Machine weight approx.: 7.8 t without oil filling - Oil filling approx.: 260 litres, 230 kg Two identical machines (built 1991, 1993) are available.

clamping force 800 kN︱injection volume 78 cm³︱screw diameter 25 mm︱platen size 570 x 552 mm︱

---

Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN08 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm - Control: CC 90-A0 Injection unit: - Injection volume max.: 78 cm³ - Injection weight max.: 90 g - Screw diameter: 25 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 400 rpm - Injection flow: 87 g/sec - Injection flow (increased): 64 g/sec - Specific injection pressure: 2400 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 185 l - Weight approx.: 4.000 kg

clamping force 2500 kN︱injection volume 2x 190 cm³︱screw diameter 45 mm︱screw length 22 D ︱platen size 510 x 670 mm︱

---

Condition: used Specification: Vertical Injection Moulding Machine for Rubber - second-hand - clamping force: 2500 kN - screw diameter: 45 mm - screw length: 22 D - screw speed: max. 300 rpm - injection volume: 2 x 190 cm3 - Injection pressure: 1900 bar - Number of heating zones: 5 - open nozzle with nozzle head - Clear column spacing: 510 x 670 - Mains supply voltage: 380 V, 50 Hz - Machine weight approx.: 7.8 t without oil filling - Oil filling approx.: 260 litres, 230 kg Two identical machines are available.

clamping force 800 kN︱injection volume 154 cm³︱screw diameter 35 mm︱platen size 570 x 552 mm︱

---

Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm Injection unit: - Injection volume max.: 154 cm³ - Injection weight max.: 156 g - Screw diameter: 35 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 320 rpm - Delivery flow: 35 g/sec - Injection flow: 148 g/sec - Injection flow (increased): 107 g/sec - Specific injection pressure: 1600 bar - Specific injection pressure increased: 2200 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN - Control: CC 90-A02 Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 155 l - Weight approx.: 3,100 kg

clamping force 1600 kN︱injection volume 2x 113 cm³︱screw diameter 40 mm︱screw length 21 D ︱platen size 410 x 570 mm︱

---

clamping force 300 kN︱injection volume 105 cm³︱screw diameter -- mm︱platen size 300 x 400 mm︱

---

Condition: used, Specification: Vertical C-frame Injection Moulding Machine for rubber - second-hand suitable for vulcanising together extruded rubber profiles to sealing frames or for the production of small precision moulded parts. The C-frame design ensures very good mould accessibility accessibility of the tools from three sides, so that when vulcanising the necessary space when vulcanising sealing profiles. to be able to work comfortably even with multiple tools. be able to work comfortably. Injection unit: - Injection volume approx.: 105 cm³ - Injection pressure approx.: 1,800 bar Clamping unit: - Clamping force: 300 kN - Size of heating platen: 300 x 400 mm - Clamping speed: 100 mm/sec - Heating power per platen: 3 kW - Total power with sliding table: 9 kW With alternating sliding table, i.e. two moulds can be used at the same time. two moulds at the same time. - Dimensions approx.: 2.400 x 1.400 x 2.600 mm - Weight approx.: 3,000 kg